Operation Instruction 11//33”” CCCCDD PPoolleessttaarr TTrruuee DDaayy//NNiigghhtt WWeeaatthheerrpprrooooff IIRR CCaammeerraa wwiitthh
CHAPTER 2 INSTALLATION 5 Dimension of whole camera with bracket 275mm/10.8” 107.5mm/4.3” 243.5m
CHAPTER 2 INSTALLATION 61.5 Camera Component Description EZ550 Component description Bracket Sun shield Fixing scr
CHAPTER 2 INSTALLATION 71.6 Back Panel Layout 1. Video Output Connector Connect the video output of the camera to a
CHAPTER 2 INSTALLATION 8 5. Control key selection switch Switch to OSD to control OSD menu by using the control key or switch to LENS to adjust zoomi
CHAPTER 2 INSTALLATION 13 Installation This chapter will describe, in general terms, how to install the EZ550 camera. STEPS: 1. Wire and mount th
CHAPTER 2 INSTALLATION 14 2. Fix the bracket to wall by using 4 screws. 3. Open camera’s back cover: Loose the 2 screws from the back
CHAPTER 2 INSTALLATION 15 4. Take off the cap of waterproof conduit which is at the camera bottom. Note: 1. the holes of waterproof
CHAPTER 2 INSTALLATION 16 Note: 1. Power cable’s diameter must be less than 10 mm 2. Only use RG59/5C2V for Video cable 3. RS485 cable must be
CHAPTER 2 INSTALLATION 17 7. Fix the camera body to bracket by using the 4 shorter screws. 8. Connect RG59 coaxial cable with
CHAPTER 2 INSTALLATION 18 10. Close the back cover and screw the 2 screws firmly. Now, you are done with the installation. NOTE: Before you clos
2 EVERFOCUS ELECTRONICS CORPORATION P/N: MZ55G00200_Ver. B Operation Instruction © 2008 EverFocus Electronics Corp Please read this manual fi
CHAPTER 2 INSTALLATION 19 2.3 Adjusting Lens Open camera’s base, a control key is attached at inner side of the base. Detach the control key an
CHAPTER 2 INSTALLATION 20 Turn the mini-joystick Up (c) or Down (d) to adjust zoom in / zoom out, Turn the mini-joystick Left (e) or Right (f) to
CHAPTER 2 INSTALLATION 21 3. EZ550 recognizes EVF-1, EVF-2 and Pelco-D protocols automatically. (No setting is required) 4. The camera default RS48
CHAPTER 3 OSD MENU AND CONFIGURATION 21 OSD Menu & Configuration This chapter introduces how to configure the camera OSD menu. 3.1 Control Key Ge
CHAPTER 3 OSD MENU AND CONFIGURATION 22 When the item with sub-menu is selected, press the mini-joystick to switch to the sub-menu for further settin
CHAPTER 3 OSD MENU AND CONFIGURATION 23 3.2 RS485 ID & Baud Rate Setting Note: This section is optional preserved for the people that want to ch
CHAPTER 3 OSD MENU AND CONFIGURATION 24 b. RS485_ID- adjustable 01~99. Default value is 99. Move joystick RIGHT and LEFT to adjust it. RS4
CHAPTER 3 OSD MENU AND CONFIGURATION 25 d. DATA STORED- Confirm with you that the last 3 settings you have made will be saved. e. ENTE
CHAPTER 3 OSD MENU AND CONFIGURATION 26 3.3 OSD Menu Setup Please make sure control key selection switch is at OSD position. Note: Unlike setting Ca
CHAPTER 3 OSD MENU AND CONFIGURATION 27 NOTE: Since DC lens is a built-in lens for EZ550 camera, shutter does not support ESC and Manual functions. E
3Precautions 1. Do not place any object on top of the cover. 2. Be careful when handling the camera, do not drop it or subject it to strong shock o
CHAPTER 3 OSD MENU AND CONFIGURATION 28 3.3.3 WHITE BALANCE control The screen color can be adjusted by using the WHITE BALANCE function. 1. Please
CHAPTER 3 OSD MENU AND CONFIGURATION 29 2. Select the mode you would like to operate by turning the mini-joystick LEFT (e) or RIGHT (f).
CHAPTER 3 OSD MENU AND CONFIGURATION 30 As the level of gain changes, the background noise in the low light level automatically decreases. 1. Plea
CHAPTER 3 OSD MENU AND CONFIGURATION 31 3. Press the mini-joystick when you finish all the settings. 3.3.8 SPECIAL 1. Please direct
CHAPTER 3 OSD MENU AND CONFIGURATION 32 3) Press the mini-joystick. 4) Maximum 15 letters can be used for the ID. ¾ Turning the mini-joystick UP (c
CHAPTER 3 OSD MENU AND CONFIGURATION 33 3.3.8.3 SYNC There are two SYNCHRONIZATION modes: INTERNAL and EXTERNAL LINE-LOCK. In LINE-LOCK mode, without
CHAPTER 3 OSD MENU AND CONFIGURATION 34 z Additionally, it is possible to change the position of the area. Please refer to the following
CHAPTER 3 OSD MENU AND CONFIGURATION 35 4. Increase RIGHT scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT: 20 and RIGHT:
CHAPTER 3 OSD MENU AND CONFIGURATION 36 z Please turn the mini-joystick LEFT (e) or RIGHT (f) to adjust the value for size of the area to be covered
CHAPTER 3 OSD MENU AND CONFIGURATION 37 4. Increase RIGHT scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT: 20 and RIGH
4Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital dev
CHAPTER 3 OSD MENU AND CONFIGURATION 38 -OFF: Disable the SHARPNESS mode. z Please press the mini-joystick. z The available range of level is 0~31.
CHAPTER 3 OSD MENU AND CONFIGURATION 39
CHAPTER 4 CONTROL FROM KEYBOARD 40 Control from Keyboard EKB500 (Optional) Note! Before being able to control keyboard, make sure Keyboard RS485 c
CHAPTER 4 CONTROL FROM KEYBOARD 41 d. Move the joystick RIGHT (f) and LEFT (e) to adjust the mode and parameters of the selected item. e. Press
CHAPTER 4 CONTROL FROM KEYBOARD 42 Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26
5Table of Contents 1.1 Features ...
CHAPTER 2 INSTALLATION 1Product Overview EZ550 camera is a true day/night, long range IR bullet style color camera. With Polestar sens-up 128x, it o
CHAPTER 2 INSTALLATION 21.2 Accessory Parts List Please be careful when you unpack the box due to the electronics devices inside. Check and make sur
CHAPTER 2 INSTALLATION 31.3 Specifications Items Parameter Pickup Device 1/3” SONY Super HAD CCD Picture Elements 768 x 494 (NTSC) ; 752 x 582 (P
CHAPTER 2 INSTALLATION 41.4 Dimensions Drilling Dimension of holes to holes Dimension of Bracket 45mm/1.8” 80mm/3.2” CHAPTER 1 PRODUCT OVER
Comments to this Manuals